Browse Categories by Agriculture

Verbatim Video Series Part IV: Recording Voice Messages

Posted by jBrown on Thu, Jul 7, 2011 @ 2:08 PM

Part four in RACO’s six-part video series shows how to record voice messages for the Verbatim autodialer. http://www.youtube.com/watch?v=putZCBe_XH0 Now that you have programmed your alarm system, you can start recording voice messages for alarm conditions. First, you should plan and write down all the messages you will record. Use Worksheet C in the manual to help with this process. Two different messages are used for each contact input: one for normal conditions and one for alarm, or fault, conditions. You can leave the normal condition message set to default. Here’s how y... Continue Reading

Continue ReadingView Comments (1) Share This

Tip of the Month: Dry Contact Input and Uses

Posted by jBrown on Tue, Jun 14, 2011 @ 5:21 PM

A dry contact or digital input is a set of switch contacts that have no other circuit or voltage wired to them. These contacts can signal the Verbatim to perform several functions: set the alarm on a set of normally open or closed contacts, report the status of a set of contacts, inquire about the digital inputs of contacts that have been closed and more. It can also be programmed on an individual basis. Click here for a complete list of dry contact functions or visit RACO’s Support Center for more information.... Continue Reading

Continue ReadingLeave a Comment Share This

Verbatim Video Series Part III: Programming the Alarm System

Posted by jBrown on Tue, Jun 7, 2011 @ 4:23 PM

Part three in RACO’s six-part video series covers programming the Verbatim autodialer’s alarm system. Part A http://www.youtube.com/watch?v=E9vOiC5vC0U Part B http://www.youtube.com/watch?v=d2KKqmOWuWE Now that you have your Verbatim Alarm System, it is time to program your unit. Following are instructions of how to finish the initial setup. 1. Clear and reset the system Turn the unit on and press the program button. This puts the device in program mode. Erase the system memory by dialing 9-3-5-9 and then press the enter button. 2. Phone number programming Now th... Continue Reading

Continue ReadingLeave a Comment Share This

Tip of the Month: Connecting Verbatim Gateway to CompactLogix PLC

Posted by jBrown on Fri, May 20, 2011 @ 12:13 PM

Verbatim Gateway autodialers can be connected via DF1 to any of Allen-Bradley’s CompactLogix family of PLCs, which have a 9 PIN, male RS232 port. The following tips will help you get started. 1. Prepare your equipment: You will need a Verbatim Gateway autodialer and 510VAB-1 cable, supplied by RACO, and a CompactLogix PLC, RS232 cable and RSLogix software, supplied by Allen-Bradley. 2. Set up CompactLogix communications: Launch the RSLogix software, then use the tabs to set up the serial and system protocol. Next, configure the CompactLogix base tags. Map the tags to the SLC platform ... Continue Reading

Continue ReadingView Comments (1) Share This

Verbatim Video Series Part II: Installation

Posted by jBrown on Fri, May 13, 2011 @ 2:12 PM

Part two in RACO’s six-part video series covers installing the Verbatim autodialer. http://www.youtube.com/watch?v=adp0Yk9dmko 1. Choose a mounting location This location must be free from condensing humidity and have temperatures between 20°F and 130°F. The autodialer must be within 5 ft of a standard RJ11 phone jack and a grounded 120-V AC outlet. It is possible to mount Verbatim outdoors with the optional enclosure. An optional heater and thermostat is also available to keep the unit at the proper temperature. 2. Get connected Next, complete all of the autodialer’s wiri... Continue Reading

Continue ReadingLeave a Comment Share This
Page 8 of 10« First...123...678910